新聞中心
日新月異的深科達
精品推薦 | 倒裝芯片貼合機
2023-11-08 16:17
優點介紹
Advantages
熱親和柔性設計，高效貼裝無極限
設備整體采用熱親和柔性設計，在保證產品整體產能的同時，能極大提高產品的貼裝精度；在關閉UP LOOK相機的情況下，設備產能可達5000PCS/h以上，在開啟UP LOOK相機的情況下，可達3000PCS/h以上，同時它能保證貼合精度在±7μm（3δ）之內。
一機多能，兼容三種封裝工藝
設備兼容芯片正裝、芯片倒裝、芯片堆疊封裝三種封裝工藝；配備擺動旋轉機構和翻轉機構，使設備能同時兼容正裝和倒裝兩類不同的貼裝工藝。配備UplookAlign和Postbond功能，Postbond功能支持實時動態檢測和動態補償，進一步確保了產品貼裝的精度和穩定性。
The device is compatible with three packaging processes: chip forward packaging, chip flip packaging, and chip stacking packaging;Equipped with a swinging and rotating mechanism and a flipping mechanism, the equipment can be compatible with two different mounting processes: forward and reverse. Equipped with UplookAlign and Postbond functions, the Postbond function supports real-time dynamic detection and compensation, further ensuring the accuracy and stability of product placement.
自動調寬與升降，封裝無憂慮
支持軌道寬度自動調節，以兼容不同寬度的載板。軌道平臺擁有基準高度調節和快速升降功能，分別用于堆疊封裝時的高度自動調整和有加熱需求時的過熱脫離。
Support automatic adjustment of track width to be compatible with carrier plates of different widths. The track platform has reference height adjustment and fast lifting functions, which are used for automatic height adjustment during stacking packaging and overheating detachment when there is a heating demand.
多尺寸兼容，快換治具任你選
兼容性強，可快換治具兼容6吋、8吋和12吋晶圓，也可使用快換治具兼容華夫盤或Gelpack上料。
Strong compatibility, quick change fixtures are compatible with 6 inch, 8 inch, and 12 inch wafers, and can also be used for wafer or Gelpack loading.
多元配置，工藝需求無遺漏
前軌道支持正裝中轉、反裝蘸膠、下相機對位等多種配置，以適配客戶不同的工藝需求。
The front track supports various configurations such as forward transfer, reverse dip glue, and lower camera alignment to meet the different process requirements of customers.
多段電流保護，快速穩定
載板壓板和載板夾爪采用多段電流控制系統，在保證快速下壓和快速夾緊的同時，有效降低對載板的沖擊。
The load plate pressing plate and load plate clamping claw adopt a multi-stage current control system, which ensures fast pressing and clamping while effectively reducing the impact on the load plate.
創新設計，高效便捷
助焊劑大小及厚度通過前方的槽大小及深度控制，助焊劑刷取板采用無螺釘設計，可以通過拉取直接實現快換；同時，高慣量比動力，可實現每小時3000次助焊劉送料。
The size and thickness of the flux are controlled by the size and depth of the groove in front, and the flux brush plate adopts a screwless design, which can be directly replaced by pulling; High inertia ratio power, able to achieve 3000 times of auxiliary welding and feeding per hour.
智能感應，適應面廣
助焊劑倉帶缺料感應裝置，當助焊刻所剩量不足時，會閃爍黃燈并在人機窗口提醒人工注入助焊刻；其中蘸膠最小0.5*0.5mm，最大20*20mm。
The flux bin is equipped with a shortage sensing device. When the remaining amount of flux is insufficient, a yellow light will flash and remind manual injection of flux in the human-machine window; The minimum amount of glue dipped is 0.5 * 0.5mm, and the maximum amount is 20 * 20mm.
自定義路徑，滿足需求，點膠更靈活
自研自定義點膠路徑編輯系統，客戶可根據實際需求繪制所需畫膠路徑。
Self developed custom dispensing path editing system, allowing customers to draw the desired dispensing path according to their actual needs.
貼合相機模塊，熱親和與柔性設計，氣冷精準定位
移動支座和位置檢測部分采用熱親和設計和柔性設計，極大程度避免了由溫變導致的精度丟失，同時加裝了氣冷流道裝置，進一步降低溫升，以保證對位精度。
The mobile support and position detection parts adopt a hot affinity design and flexible design, greatly avoiding accuracy loss caused by temperature changes. At the same time, an air-cooled flow channel device is installed to further reduce temperature rise and ensure alignment accuracy.
降低誤差，精準貼合
邦頭水平移動結構的支座和位置檢測部分采用熱親和設計和柔性設計，降低了電機溫升帶來的誤差，保證了貼合精度。
The support and position detection part of the Bangtou horizontal moving structure adopts a hot affinity design and flexible design, reducing the error caused by motor temperature rise and ensuring the fitting accuracy.
精準力控，自適應軟著陸
自適應軟著陸式邦頭力控系統，確保邦頭在快速拾取+貼合的同時，消除拾取和貼合過程中速度變化帶來的沖擊，從而確保拾取和貼合力的精度，在250gf以下力控誤差低于5%。
精準調節，完美貼合
Bondhead 齒輪式水平調節裝置調節水平如同上發條一樣便捷與精準;保證貼合面完全與貼合基準面重合，完成對超薄芯片的無損貼合。
The level adjustment device of the Bondhead gear type is as convenient and accurate as the upper spring for adjusting the level; Ensure that the bonding surface completely overlaps with the bonding reference plane, completing non-destructive bonding of ultra-thin chips.
輕擺臂+鑄鐵支撐，振動小，取放快
輕量化擺臂+鑄鐵支撐立柱，保證了高頻快速取放料的同時，有效降低了高速擺臂造成的振動，確保了設備的整體穩定性。
The lightweight swing arm and cast iron support column ensure high frequency and fast material collection and discharge, while effectively reducing the vibration caused by high-speed swing arms, ensuring the overall stability of the equipment.
直驅頂針，精度更高，響應更快
直驅式頂針機構，相對凸輪機構精度更高，響應更迅速，且其頂出距離，頂出高度，頂出速度均可設置。
The direct drive ejector pin mechanism has higher accuracy and faster response compared to the cam mechanism, and its ejection distance, ejection height, and ejection speed can be set.
雙驅動協同，精確微距，高效保護
雙驅動裝置，可使頂針與頂針吸盤獨立進行微距運動，相互配合下，能有效保護產品，提高生產效率。
The dual drive device allows the ejector pin and ejector pin suction cup to independently move at a macro distance, and in combination, it can effectively protect the product and improve production efficiency.
多頂方案，超薄無憂
當需要分離超薄芯片時，頭部可更換為多級頂針剝離裝置，最小可剝離30um厚度芯片。
When it is necessary to separate ultra-thin chips, the head can be replaced with a multi-level ejector pin stripping device, which can strip chips with a minimum thickness of 30um.
設備外形
Equipment appearance
相關新聞
關注公眾號
深圳總部：深圳市寶安區西鄉街道龍騰社區匯智研發中心BC座B1001 惠州基地：廣東省惠州市惠城區月明路惠州深科達智能裝備產業園
版權所有◎深圳市深科達智能裝備股份有限公司 粵ICP備12028729號 網站建設：中企動力 深圳 SEO